issue notes - m109 turns off heater and jr goes unresponsive

— gcode from the 1st attempt at a print

13:45:40.293 : N295 M106 S255 75 13:45:40.824 : N296 M105 10 13:45:41.621 : N297 M107 9 13:45:42.605 : N298 M106 S255 70 13:45:43.501 : N299 M107 7 13:45:43.880 : N300 M105 4 13:45:46.936 : N301 M105 5 13:45:49.998 : N302 M105 6 13:45:51.152 : N303 M104 S185 73 13:45:53.055 : N304 M105 0 13:45:54.093 : N305 M104 S0 67 13:45:56.109 : N306 M105 2 13:45:59.166 : N307 M105 3 13:46:02.228 : N308 M105 12 13:46:05.284 : N309 M105 13 13:46:08.341 : N310 M105 5 13:46:11.400 : N311 M105 4 13:46:14.456 : N312 M105 7 13:46:17.513 : N313 M105 6 13:46:20.574 : N314 M105 1 13:46:23.647 : N315 M105 0 13:46:26.702 : N316 M105 3 13:46:29.775 : N317 M105 2 13:46:32.830 : N318 M105 13 13:46:35.890 : N319 M105 12 13:46:38.946 : N320 M105 6 13:46:42.004 : N321 M105 7 13:46:45.062 : N322 M105 4 13:46:48.120 : N323 M105 5 13:46:51.176 : N324 M105 2 13:46:54.236 : N325 M105 3 13:46:57.307 : N326 M105 0 13:46:58.866 : N327 M106 S255 67 13:46:59.750 : N328 M107 12 13:47:00.369 : N329 M105 15 13:47:01.949 : N330 M106 S255 69 13:47:02.757 : N331 M107 4 13:47:03.426 : N332 M105 5 13:47:06.479 : N333 M105 4 13:47:08.003 : Starting object analyser … 13:47:08.080 : Points:344 13:47:08.080 : Edges:1026 13:47:08.080 : Faces:684 13:47:08.080 : Shells:1 13:47:08.080 : Object is manifold. 13:47:08.086 : Analysing finished. 13:47:08.086 : Starting object analyser … 13:47:08.088 : Points:344 13:47:08.088 : Edges:1026 13:47:08.088 : Faces:684 13:47:08.088 : Shells:1 13:47:08.088 : Object is manifold. 13:47:08.088 : Analysing finished. 13:47:09.542 : N334 M105 3 13:47:11.320 : Slic3r command:C:Files-Host3r3r.exe –load “C:3r.ini” –print-

center 70,55 -o “C:.gcode” “C:.obj” 13:47:11.929 : => Processing triangulated mesh 13:47:12.454 : => Generating perimeters 13:47:12.602 : N335 M105 2 13:47:13.155 : => Detecting solid surfaces 13:47:13.217 : => Preparing infill surfaces 13:47:13.218 : => Detect bridges 13:47:13.222 : => Generating horizontal shells 13:47:13.226 : => Combining infill 13:47:13.226 : => Infilling layers 13:47:13.499 : => Generating skirt 13:47:13.504 : => Exporting G-code to C:.gcode 13:47:14.158 : Done. Process took 0 minutes and 2.230 seconds 13:47:14.159 : Filament required: 303.8mm (0.7cm3) 13:47:14.445 : N336 G21 60 13:47:14.449 : N337 M107 2 13:47:14.465 : N338 M104 S200 79 13:47:14.469 : N339 G28 58 13:47:31.225 : N340 M105 0 13:47:31.236 : N341 G1 Z5 F5000 34 13:47:31.242 : N342 M109 S200 79

… unresponsive at this point, temp not rising note: fan on = m106 255, fan off = m107 —-

13:50:30.610 : N19 M105 63 13:50:30.801 : => Generating skirt 13:50:30.804 : => Exporting G-code to C:.gcode 13:50:31.446 : Done. Process took 0 minutes and 2.033 seconds 13:50:31.447 : Filament required: 303.2mm (0.7cm3) 13:50:31.706 : N20 G21 8 13:50:31.709 : N21 M107 54 13:50:31.732 : N22 M104 S200 119 – heat extruder 13:50:31.742 : N23 G28 2 – home 13:50:36.452 : N24 M105 49 – get extruder temp 13:50:36.463 : N25 G1 Z5 F5000 19 – move z axis up a bit 13:50:36.468 : N26 M109 S200 126 – heat extruder and wait

.. unresponsive, not heating

—- try manually G21 M107 M104 S200 G28 – home M105 G1 Z5 F5000 – move z axis up a bit M109 S200 – heating extruder DEATH OCCURS HERE

at this point, sending commands manually results in “command waiting…” still getting temperature data (and temp goes down, not up to 200)

—- try manually again

M109 S200 – heating extruder DEATH OCCURS HERE AGAIN

sending JUST THIS command results in “Heating extruder” showing up in the manual control, and “1 Command Waiting” in the status bar

when the heater is already above 200, the M109 command will go to “command waiting” for a little bit, and then return…

but it’s not doing that automatically when printing, just manually. When I manually set the extruder to 210, and then go to print something, it still dies when the print job sends it the m109